No products in the cart.
Parker
-
$91.99
$223.97Parker L319 SUNISO 4GS 1 GAL (VG-4 MO -1)
$91.99$223.97 -
$712.99
$1,735.97Parker OIL FILTER W/BYPASS OF-303-BP
$712.99$1,735.97 -
$655.49
$1,595.97Parker Oil Filter Sporlan OF-303-BP, 3/8” MF
$655.49$1,595.97 -
$65.99
$119.98Parker Tko Acid Test Kit TKO | Lubricants
$65.99$119.98 -
Parker Etk Poe Acid Test Kit ETK | Lubricants
Parker Hannifin Refrigeration Oil Acid Test KitSimilar to the TKO test kit, but formulated for POE lubricants. Designed specifically for use with polyol ester lubricants. Test for acid contamination in the compressor’s crankcase which can be indicative of lubricant decomposition.Features:Adjusted for the higher acid levels of POE lubricantsIf test remains purple, the oil is safe. If it turns yellow, acid is too highUltra-sensitive color change guarantees an accurate test. Marginal conditions cause partial color changesColor comparison chart in every boxEasiest way of determining if the acid level of polyol ester (POE) compressor lubricants is considered safe or too acidic. POE lubricants are actually created by reacting an alcohol with an acid. Although the total acid numbers are higher than in comparable mineral oils, the chemical make-up of POE lubricants keeps this number relatively low. However, this lubricant can break down into its acid and alcohol componentseither from excessive heat such as a motor burn-out or high discharge temperatures, or with excessive system moisture. This acid can cause damage to a system and may eventually cause the system to fail prematurely. It is important that such a condition bediagnosed early and that system be cleaned up according to proper industry procedures.
$65.99$119.98Parker Etk Poe Acid Test Kit ETK | Lubricants
$65.99$119.98 -
Parker Flocon A82-54 – Epr, 2-5/8 F.Sw Conn, 2-1/8 Port 102927 | Line Components
The A8 has a unique modular design that allows the commercial pressure regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be created, while pilot adaptors can be changed out to add features or even change functions. Thus, retrofitting for additional evaporator capacity, heat reclaim, or hold back for hot gas defrost is simple and requires no pipe line revisions under most circumstances. These valves will modulate to maintain a pressure as set for in the field, in spite of fluctuations in load, changes in ambient, changes in available refrigerant flow paths, and other operating variances. Appropriately sized, these valves will modulate the flow of liquid or vapor, high side or low side in a wide variety of system arrangements used in industrial, commercial and air conditioning installations. Models are available in combinations of connection sizes, port sizes, functions and features as designated by the model code, for application in a wide variety of control functions on industrial, commercial and air conditioning systems.Three control functions are available:Inlet, Outlet, and Differential pressure control. Two control features can be added by incorporating pilot solenoids; either Electric Shut-Off(S) or Electric Bypass (B); also called Wide-Opening.The valves are an integrated assembly of four modules:1) A body, which contains no moving parts, but is ordered to suit a particular connection size;2) A capacity cartridge, which contains both piston and modulating plug, and defines the Port Size;3) A pilot adapter, which defines the valve function and onto which the Pilot Solenoids providing either the “S” or “B” feature are added as required;4) The bonnet, containing the Range Spring and adjustment screw, which mechanisms are set for the value of pressure which the valve is to maintain
$7,083.99$12,879.98Parker Flocon A82-54 – Epr, 2-5/8 F.Sw Conn, 2-1/8 Port 102927 | Line Components
$7,083.99$12,879.98 -
Parker Flocon A82-42 – Epr, 2-1/8 F.Sw Conn, 1-5/8 Port 102923 | Line Components
The A8 has a unique modular design that allows the commercial pressure regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be created, while pilot adaptors can be changed out to add features or even change functions. Thus, retrofitting for additional evaporator capacity, heat reclaim, or hold back for hot gas defrost is simple and requires no pipe line revisions under most circumstances. These valves will modulate to maintain a pressure as set for in the field, in spite of fluctuations in load, changes in ambient, changes in available refrigerant flow paths, and other operating variances. Appropriately sized, these valves will modulate the flow of liquid or vapor, high side or low side in a wide variety of system arrangements used in industrial, commercial and air conditioning installations. Models are available in combinations of connection sizes, port sizes, functions and features as designated by the model code, for application in a wide variety of control functions on industrial, commercial and air conditioning systems.Three control functions are available:Inlet, Outlet, and Differential pressure control. Two control features can be added by incorporating pilot solenoids; either Electric Shut-Off(S) or Electric Bypass (B); also called Wide-Opening.The valves are an integrated assembly of four modules:1) A body, which contains no moving parts, but is ordered to suit a particular connection size;2) A capacity cartridge, which contains both piston and modulating plug, and defines the Port Size;3) A pilot adapter, which defines the valve function and onto which the Pilot Solenoids providing either the “S” or “B” feature are added as required;4) The bonnet, containing the Range Spring and adjustment screw, which mechanisms are set for the value of pressure which the valve is to maintain
$6,588.99$11,979.98Parker Flocon A82-42 – Epr, 2-1/8 F.Sw Conn, 1-5/8 Port 102923 | Line Components
$6,588.99$11,979.98 -
Parker Flocon A82-42 – Epr, 1-5/8 F.Sw Conn, 1-5/8 Port 102920 | Line Components
The A8 has a unique modular design that allows the commercial pressure regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be created, while pilot adaptors can be changed out to add features or even change functions. Thus, retrofitting for additional evaporator capacity, heat reclaim, or hold back for hot gas defrost is simple and requires no pipe line revisions under most circumstances. These valves will modulate to maintain a pressure as set for in the field, in spite of fluctuations in load, changes in ambient, changes in available refrigerant flow paths, and other operating variances. Appropriately sized, these valves will modulate the flow of liquid or vapor, high side or low side in a wide variety of system arrangements used in industrial, commercial and air conditioning installations. Models are available in combinations of connection sizes, port sizes, functions and features as designated by the model code, for application in a wide variety of control functions on industrial, commercial and air conditioning systems.Three control functions are available:Inlet, Outlet, and Differential pressure control. Two control features can be added by incorporating pilot solenoids; either Electric Shut-Off(S) or Electric Bypass (B); also called Wide-Opening.The valves are an integrated assembly of four modules:1) A body, which contains no moving parts, but is ordered to suit a particular connection size;2) A capacity cartridge, which contains both piston and modulating plug, and defines the Port Size;3) A pilot adapter, which defines the valve function and onto which the Pilot Solenoids providing either the “S” or “B” feature are added as required;4) The bonnet, containing the Range Spring and adjustment screw, which mechanisms are set for the value of pressure which the valve is to maintain
$5,532.99$10,059.98Parker Flocon A82-42 – Epr, 1-5/8 F.Sw Conn, 1-5/8 Port 102920 | Line Components
$5,532.99$10,059.98 -
Parker Flocon A81-35 – Epr, 1-5/8 F.Sw Conn, 1-3/8 Port 101722 | Line Components
The A8 has a unique modular design that allows the commercial pressure regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be created, while pilot adaptors can be changed out to add features or even change functions. Thus, retrofitting for additional evaporator capacity, heat reclaim, or hold back for hot gas defrost is simple and requires no pipe line revisions under most circumstances. These valves will modulate to maintain a pressure as set for in the field, in spite of fluctuations in load, changes in ambient, changes in available refrigerant flow paths, and other operating variances. Appropriately sized, these valves will modulate the flow of liquid or vapor, high side or low side in a wide variety of system arrangements used in industrial, commercial and air conditioning installations. Models are available in combinations of connection sizes, port sizes, functions and features as designated by the model code, for application in a wide variety of control functions on industrial, commercial and air conditioning systems.Three control functions are available:Inlet, Outlet, and Differential pressure control. Two control features can be added by incorporating pilot solenoids; either Electric Shut-Off(S) or Electric Bypass (B); also called Wide-Opening.The valves are an integrated assembly of four modules:1) A body, which contains no moving parts, but is ordered to suit a particular connection size;2) A capacity cartridge, which contains both piston and modulating plug, and defines the Port Size;3) A pilot adapter, which defines the valve function and onto which the Pilot Solenoids providing either the “S” or “B” feature are added as required;4) The bonnet, containing the Range Spring and adjustment screw, which mechanisms are set for the value of pressure which the valve is to maintain
$4,135.99$7,519.98 -
Parker Flocon A81-28 – Epr, 1-3/8 F.Sw Conn, 1-1/8 Port 101717 | Line Components
The A8 has a unique modular design that allows the commercial pressure regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be created, while pilot adaptors can be changed out to add features or even change functions. Thus, retrofitting for additional evaporator capacity, heat reclaim, or hold back for hot gas defrost is simple and requires no pipe line revisions under most circumstances. These valves will modulate to maintain a pressure as set for in the field, in spite of fluctuations in load, changes in ambient, changes in available refrigerant flow paths, and other operating variances. Appropriately sized, these valves will modulate the flow of liquid or vapor, high side or low side in a wide variety of system arrangements used in industrial, commercial and air conditioning installations. Models are available in combinations of connection sizes, port sizes, functions and features as designated by the model code, for application in a wide variety of control functions on industrial, commercial and air conditioning systems.Three control functions are available:Inlet, Outlet, and Differential pressure control. Two control features can be added by incorporating pilot solenoids; either Electric Shut-Off(S) or Electric Bypass (B); also called Wide-Opening.The valves are an integrated assembly of four modules:1) A body, which contains no moving parts, but is ordered to suit a particular connection size;2) A capacity cartridge, which contains both piston and modulating plug, and defines the Port Size;3) A pilot adapter, which defines the valve function and onto which the Pilot Solenoids providing either the “S” or “B” feature are added as required;4) The bonnet, containing the Range Spring and adjustment screw, which mechanisms are set for the value of pressure which the valve is to maintain
$3,904.99$7,099.98 -
Parker Strainers 2-1/2″ Rsf Strainer Less Gaskets And Flanges 100010 | Industrial Valves
The RSF and RSW industrial type Refrigerant Strainers with stainless steel screens are designed especially for the protection of Industrial Refrigeration control valves from foreign materials present in refrigeration systems. The fine stainless steel mesh will collect particles as small as 0.009” in diameter (60 Mesh@ 0.0075” wire). Generous available screen area allows maximum dirt capacity at minimum pressure drop. The RSF strainers may be close coupled to Industrial Refrigeration valves having the same flange gasket size.Markets:• Industrial Refrigeration• Commercial RefrigerationFeatures and Benefits:• Stainless Steel Screen (60 Mesh)• Drain Connection for Safe Cleaning• Generous Screen Area• Low Pressure Drop• Durable Filter Bags Available ¾” to 4” (20-100mm)- on RSF Strainers• RSF Type Strainers can be close coupledApplication:• Refrigerant System• Oil System
$3,926.99$7,139.98 -
Parker Solenoid Valve S8F-13 1/2″ No Flanges Or Coil 100997 | Industrial Valves
Parker’s S4 solenoids are the refrigeration industry’s standard for solenoid valves and have provided decades of safe and reliable operation. These valves are highly configurable and can be provided with flanges for Socket Welding, Butt Welding, ODS connections, and Threaded connections. The S4 is offered in sizes from ¾” (DN20) to 8” (DN200). These valves may be opened by means of the manual opening stem for servicing or in case of electrical power failure. As the S4 valves up to 4” feature a flanged connection they may be easily removed from the system for servicing. The S4 valves are pilot operated and require a minimum 0.21 bar (3 psi) pressure drop to fully open. The S4AD is a spring closing, pilot operated, dual-position solenoid valve which is crucial for evaporator control groups that use hot gas defrost. The dual position function of the S4AD allows the system to equalize before fully opening and can prevent liquid hammer. The S4X is an explosion proof hazardous environment type solenoid carrying a NEMA Type 4 and 7 classification.
$1,242.99$2,259.98 -
Parker Solenoid Valve S7A-25 1″ No Flanges Or Coil 100994 | Industrial Valves
Parker’s S7 series solenoid valves are available in a low pressure drop version that are capable of opening with a pressure drop less than 1 psi across the valve. This feature makes them ideal for applications where low pressure drop is important, such as low pressure liquid feed lines. The S7 is a pilot operated, positive lift, cast iron bodied valve. The valve may be opened by means of the manual opening stem for servicing or in case of electrical power failure. The Type S7 Solenoid Valve is furnished with FPT Internal NPT (U.S. Standard Taper Pipe Thread), Socket Weld, Weld Neck or ODS (solder over copper tubing of given diameter) connections.Markets:• Industrial Refrigeration• Commercial RefrigerationFeatures and Benefits:• Standard Coil Housing Meets NEMA 3R and NEMA 4- Rain Tight• Coil Housing Surpasses NEMA Salt Spray Test• Molded Class “F” Coil Construction• Pilot Light Available• Stainless Steel Needle• Manual Opening Stem• Design Pressure (MRP): 27.6 bar (400 PSIG)• Positive Lift, Held Open ElectricallyApplication:• S7A – Most Liquid or Hot Gas Lines• S7AL- Low Pressure Drop, Liquid Transfer from Intermediate to Low Pressure Vessels, and Equalizer Lines
$2,738.99$4,979.98 -
Parker Solenoid Valve S7A-20 3/4″ No Flanges Or Coil 100993 | Industrial Valves
Parker’s S7 series solenoid valves are available in a low pressure drop version that are capable of opening with a pressure drop less than 1 psi across the valve. This feature makes them ideal for applications where low pressure drop is important, such as low pressure liquid feed lines. The S7 is a pilot operated, positive lift, cast iron bodied valve. The valve may be opened by means of the manual opening stem for servicing or in case of electrical power failure. The Type S7 Solenoid Valve is furnished with FPT Internal NPT (U.S. Standard Taper Pipe Thread), Socket Weld, Weld Neck or ODS (solder over copper tubing of given diameter) connections.Markets:• Industrial Refrigeration• Commercial RefrigerationFeatures and Benefits:• Standard Coil Housing Meets NEMA 3R and NEMA 4- Rain Tight• Coil Housing Surpasses NEMA Salt Spray Test• Molded Class “F” Coil Construction• Pilot Light Available• Stainless Steel Needle• Manual Opening Stem• Design Pressure (MRP): 27.6 bar (400 PSIG)• Positive Lift, Held Open ElectricallyApplication:• S7A – Most Liquid or Hot Gas Lines• S7AL- Low Pressure Drop, Liquid Transfer from Intermediate to Low Pressure Vessels, and Equalizer Lines
$1,671.99$3,039.98 -
Parker Solenoid Valve S4A-25 1″ No Flanges Or Coil 100954 | Industrial Valves
Parker’s S4 solenoids are the refrigeration industry’s standard for solenoid valves and have provided decades of safe and reliable operation. These valves are highly configurable and can be provided with flanges for Socket Welding, Butt Welding, ODS connections, and Threaded connections. The S4 is offered in sizes from ¾” (DN20) to 8” (DN200). These valves may be opened by means of the manual opening stem for servicing or in case of electrical power failure. As the S4 valves up to 4” feature a flanged connection they may be easily removed from the system for servicing. The S4 valves are pilot operated and require a minimum 0.21 bar (3 psi) pressure drop to fully open. The S4AD is a spring closing, pilot operated, dual-position solenoid valve which is crucial for evaporator control groups that use hot gas defrost. The dual position function of the S4AD allows the system to equalize before fully opening and can prevent liquid hammer. The S4X is an explosion proof hazardous environment type solenoid carrying a NEMA Type 4 and 7 classification.
$3,365.99$6,119.98 -
Parker Solenoid Valve S4A-20 Less Flanges And Coil 100953 | Industrial Valves
Parker’s S4 solenoids are the refrigeration industry’s standard for solenoid valves and have provided decades of safe and reliable operation. These valves are highly configurable and can be provided with flanges for Socket Welding, Butt Welding, ODS connections, and Threaded connections. The S4 is offered in sizes from ¾” (DN20) to 8” (DN200). These valves may be opened by means of the manual opening stem for servicing or in case of electrical power failure. As the S4 valves up to 4” feature a flanged connection they may be easily removed from the system for servicing. The S4 valves are pilot operated and require a minimum 0.21 bar (3 psi) pressure drop to fully open. The S4AD is a spring closing, pilot operated, dual-position solenoid valve which is crucial for evaporator control groups that use hot gas defrost. The dual position function of the S4AD allows the system to equalize before fully opening and can prevent liquid hammer. The S4X is an explosion proof hazardous environment type solenoid carrying a NEMA Type 4 and 7 classification.
$2,342.99$4,259.98 -
$6,665.99
$12,119.98Parker Solenoid Valve – S5A-50 2″ No Flanges Or Coil 100982 | Industrial Valves
$6,665.99$12,119.98 -
Parker Safety Relief Valve Csrh3 350Psig 3/4X1 111650 | Industrial Valves
Parker’s cartridge safety relief valves(CSRV) are designed to offer thehighest level of protection whilemaintaining easy serviceability. TheCSRV was designed from the existingParker SR and SRH safety relief valvehousing, which allows for a simpleand easy upgrade path to the newcartridge based design.As local or state codes govern thefrequency of valve replacement, theCSRV is a cost effective alternative tostandard safety relief valve designs.Typical applications for the CSRVinclude compressor packages,accumulator vessels and anywhereelse protection from overpressure isrequired.
$2,188.99$3,979.98Parker Safety Relief Valve Csrh3 350Psig 3/4X1 111650 | Industrial Valves
$2,188.99$3,979.98 -
$1,814.99
$3,299.98Parker Safety Relief Valve Csrh2 350Psig 1/2X1 111644 | Industrial Valves
$1,814.99$3,299.98
